Features and Benefits

• Lay in lug design easily installs onto any Express Tray 2” through 4” deep without any disassembly required.
• Approved for steel and stainless steel wire mesh trays.
• Accepts 12 AWG solid through 2 AWG stranded aluminum and 14 AWG solid/stranded through 2 AWG stranded copper conductors.
• “Slotted hook” design sits securely onto the Express Tray mesh intersections to restrict swiveling.
• Must be used on each length of QuikLok series tray applications to meet CSA requirements.

4 in. Square 347V Kits

Another first from IBERVILLE made for the Canadian market. A 4 in. square box and cover kit specifically made for 347V applications.

The new kit includes a 1/2 in. raised single gang device cover factory mounted to a 4 in. square, 2-1/8 in. deep box that fulfills the requirements of the Canadian Standards Association regarding 347V applications. Standard C22.2 No. 18.1-04 Section 9.2.1.2 reads: Knockouts for the entrance of conduit or cable shall not be located in the sides of a box intended to accommodate a switch rated at
347V ac.

With a total capacity of 33.6 cubic inches, these kits offer ample room to install any 347V rated switch. The cover opening also allows the wiring to be done without having to remove the cover from the box. The box features a raised ground screw and has 2 only 1/2 in. knockouts and 1 concentric 1/2 in. and 3/4 in. knockout on the top and bottom surfaces.

Thomas & Betts is concerned about safety in electrical installations and is committed to providing code-compliant products that promote safety as well as time saving solutions to your problems. This commitment is a big part of making us the leader in our industry.

Designed, engineered and made in Canada.

• Elimination of side knockouts improves box safety in high traffic locations.
• Less chance of vandalism and personnal injury due to the side knockouts being pushed in — accidentally or on purpose — and making contact with the live terminals.
• Facilitates surface (flush) mounting.
• Raised ground screw.
• 1-7/8 in. depth, 4 in. heigth, 2-3/8 in. width.
• Two 1/2 in. knockouts in the ends.
• Two 1/2 in. knockouts in the bottom.
• 50 units per case.
• Accepts all BC11-C Utility Covers.

• CSA certified product.
• One person operation.
• No ladders or lifts required.
• Simplified maintenance.
• Hot dipped galvanized steel and aluminum finishes.
• Free’s up catwalks and walkways during maintenance.
• Epoxy coated finishes available.

Motor Lead Disconnects

Thomas & Betts offers a complete line of Motor Lead Disconnects for 600 Volt and 5KV applications. Constructed of high conductivity copper with tin plating, these disconnects achieve quick, reliable change out of electric motors while eliminating bolting, taping and loose connections.

The Motor Lead Disconnects cover the wire range from #16 through 500 kcmil and meet or exceed the electrical and mechanical performance of bolted connections. The female disconnects are equipped with a beryllium copper interface band to product dependable connections.

Color-Keyed® Motor Lead Disconnects include these prominent features:

• Quick connections – Eliminates nuts, bolts and washers.
• Reliable insulation – No more “miles” of insulating tape. Simply slide on the reusable boot, keeping the total assembly small enough to fit into tight motor housings.
• Labor savings – Fast snap-together assembly.
• Quick disconnect – No knife-cutting of melted tape, therefore no risk of cutting wire insulation, less motor downtime, and installer exposure in hostile environments is minimized.

Terminating teck cable can be a time consuming process, especially when angle adjustments are required. Current termination methods such as 90-degree elbows and LB conduit bodies take up a lot of space and lack flexibility.

To address these issues, Thomas & Betts is proud to introduce its latest “industry first” – the STAR TECK EXTREME DIRECTOR(TM) fitting, the electrical industry’s first truly adjustable, range-taking fitting.

Compared to traditional 90-degree termination methods, the STAR TECK EXTREME DIRECTOR(TM) can save on installation time by up to 50%!

Featuring an exclusive swash-plate design, the STAR TECK EXTREME DIRECTOR(TM) fitting adjusts from 90 to 180 degrees. A full circular bore makes cable insertion trouble-free. Alignment guides serve as handy reference points for aligning installed fittings at the same angle.

What’s more, the STAR TECK EXTREME DIRECTOR(TM) fitting requires no disassembly prior to installation and can also be easily disconnected.

• The most cubic capacity of any metallic device box available in Canada
• Quick Easy Mounting
• All the “LHTQ” time saving features
• CSA approved one screw mounting
• Designed and manufactured in Canada

Presenting an efficient and practical extension to our line of connectors. The CI4006-FP3 (60 per pack) is an innovation in the connector world. The main feature of this connector is the ratcheting locking clamp mechanism that allows you to pull the required lenght of cable through the connector before locking it into position. It also allows you to make adjustments when too much cable has been pulled through the connector. Even after the installation is complete, the ratcheting locking clamp can be released and the connector can be repositioned. When dealing with rework or limited space situations, the connector can be installed from the inside of the enclosure. Another great example of it’s versatility. Here is a list of characteristics:

• designed for use on 6/3 or 8/3 non-metallic sheated cables
• allows for adjustments or changes after installation
• assures a strong grip on a wide range of cables
• facilitates installations and prevents damaged cables
• improves productivity

Thomas & Betts is concerned about safety in electrical installations. We are committed to providing code-compliant products that promote safety as well as time saving solutions to your problems. This commitment is a big part of making us a leader in our industry.

What makes this kit different from the 1st generation?

It contains everything the OD-TOOL-KIT has with the exception of having an ODB1 compression tool with straight fiberglass handles and an insulated head cover (ODBH1) pre-installed. The introduction of the OD-TOOL-KIT-I to the market now offers contractors an option to connect to live Hydro power lines.

• Power-tool compatible for fast and efficient installation
• Patented pre-set torque mechanism takes the guesswork out of installation, delivering optimum torque even when using power tools
• Pre-set torque prevents over-tightening and excess pressure on delicate cables
• Anti-vibration nut ensures permanent installation even in high-vibration environments
• Superior design load capabilities for heavy-duty applications:
  - 350 lb for 1/2” to 2-1/2” trade sizes
  - 450 lb for 3” to 4” trade sizes

Handle Retrofit Trapeze Applications with Ease!

The innovative Superstrut Trap-Eze Connector changes a timeconsuming retrofit trapeze application into a streamlined process. Using a Superstrut Trapnut Strut Fastener, the new Trap-Eze Connector can be easily installed above or to the side of an existing assembly, eliminating the need to disassemble and reassemble the trapeze. It is designed for use with shorter strut lengths that can vary in length by as much as an inch, so the strut can be rough cut versus labor-intense precision cuts.

• Easily installs above or to the side of an existing assembly, eliminating the need to disassemble and reassemble the trapeze
• Connectors can be reused upon disassembly of a trapeze
• Designed for either 3/8” and 1/2” threaded rod
• Designed for use with the innovative Superstrut Trapnut Strut
• Fastener, which can take up to 43% less time than standard nuts and washers on retrofit trapeze applications
• View window provides safety zone for strut length

This kit has been created to help contractors and installers to easily have access to the identificationsMarkers required to properly and quickly ID the installed meter sockets. These markers are clipped to the upper lip of the enclosure and provide permanent customer identification.

• facilitates installations and prevents damaged cables
• enforces code-compliant cable installations
• improves productivity

This new kit is complete with 15 dies and has been created to “EZ” you into all your crimping and grounding die requirements. This new kit includes 15 die sets and has been created for all types of connections: copper conductors to copper connectors, copper conductors to aluminum connectors, aluminum conductors to aluminum connectors and finally, all our E-Z-GROUND(®) compression connections. This Thomas & Betts kit is the most complete!

Features:

• EXCLUSIVE
• Manufactured from TPE, concrete tight
• Flexible hinge provides alignment of
  pass-through with ceiling
• Bellows – mounts to vertical walls and angled walls up to 30º
• Quick and easy installation
• Eliminates the use of duct tape and clamps
• Manufactured to IPS dimensions for use with most conduit types
• Superior aesthetics (blends in to the concrete)
• Trade sizes: 2”, 3”, 4” and 6”
• Future-proofs the structure. Pass-through remains dark and protected until needed
• Note: Firestop (where needed) and conduit NOT INCLUDED

Features:

Carlon® PV-Mold is a non-metallic pole riser system designed to protect communication and power cable installed on poles.

We have added the contractor preferred features of our SSX brackets to our BC1110 utility box which makes it quick and easy to install on metal studs.

Features

• Save time and effort! Roomier box has the practical features you need to work more effectively. Clear positioning guides take the guesswork out of box installation.
• 14% added capacity! With 14.25 cu. in. instead of the standard 12.5 cu. in., this box is able to accomodate a greater number of conductors.
• The easiest, most accurate installation ever! Clearly marked positioning guides for drywall and outside wall applications. Retractable positioning guides for double-drywall.

Technical Specifications:

• Non-insulated or insulated connectors
  (suffix “IT”)
• Concrete-tight
• Models 1-1/2” to 4” are also suitable for rigid and IMC conduits
• Combo head screws
  (Slot-Philips-Robertson screwdrivers)

10 solid reasons to buy Bore-Gard(®)

• Wide range: from #8 to 4/0 AWG copper lugs and splices
• Installs lugs and splices: Series 54000 and 58000
• 8-position color-coded rotating dies
• Comfortable hand grip
• Die index embossment for permanent inspectability

The Simplest and Best Way to Splice Multiple Conductors of Varying Sizes!

Color-Keyed(®) Parallel Splices offer conductor-splicing solutions for hundreds of OEM, utility and communications applications. They’re especially well suited for use in the manufacturing, repair and servicing of windings for transformers, motors, generators and turbines. Rely on them for excellent reliability, long-term performance and a CSA certified connection at a low installed cost.

The Color-Keyed(®) Battpac(®) LT4-Ton Inline Cordless Crimp Tool combines a lightweight, balanced, ergonomic design and extremely quiet operation with minimal vibration for superior user comfort. For convenience, its closed-yoke head rotates 180° for easy access in tight spaces but can be opened to enable crimping of connected wiring.

The new, revolutionary, patented design Carlon(®) PVC Conduit Repair System significantly reduces the time and money associated with repairing broken PVC conduits a.k.a. “stub-ups” in concrete slabs.

The system is a line of couplings, adapters, reamers and plugs designed to allow contractors to quickly and easily repair broken PVC conduits without having to chip away and repour concrete, while still maintaining the inside diameter of the conduit.

Simply cut off the broken conduit; ream the I.D. of the conduit and insert a coupling or adapter, it’s that easy. A job that normally takes 20 minutes can now be done in 2 minutes or less!

• Attaches a full range of EMT, rigid conduit and cable to strut channels.
• Multi-driver combination bolt head accepts a wrench, screwdriver or nut driver.
• Specifically designed for small diameter cables. (fire alarm, data, etc...)
• Remove cable or pipes easily without disturbing neighbouring clamps.

• Wood floor application
• Drop in for wood floors
• Low voltage adjustable
• For wood and concrete floors
• Slab floor box

• Flush Service Floor Boxes
• Outlets at Floor Level
• Concealed Service Floor Boxes
• Outlets Below Floor Level
• Poke Through Systems
• Access Floor Modules (AFM) for Raised Floors

• Open-yoke design provides maximum crimping flexibility
• Double-speed feature maximizes efficiency by doubling jaw speed until it reaches load capacity
• Powerful Ni-MH battery yields more crimps per charge
• Crimps up to 600 kcmil copper or 400 kcmil aluminum lugs and splices
• Ships complete with 16 TBM Series hex crimp dies for 8 AWG to 500 kcmil copper (10 AWG to 350 kcmil aluminum)
• Also accepts Blackburn(®) O and D Series Dies
• Compatible with Burndy “W” dies
• Approximately 200 crimps per battery charge (based on 3/0 AWG)

• One hole copper compression lugs from #8   standard to   #2 (CTL Series)
• Long Barrel Splices (CU Series)
• One TBM4BB, color-coded Comfort Crimp(TM) installation tool.

• Requires no heat gun or adhesive to form a moisture-proof, abrasion-resistant bond
• Easy-release, non-static-sensitive, high-visibility liner peels right off
• Self-Fusing tape material adheres to itself for ease of installation
• Creates an immediate, permanent bond even when wet no waiting period
• Offers high dielectric strength, suitable for both high and low voltage applications (class ‘‘H’’)
• Stable even under extreme temperature: -90ºC (-130ºF) to 260ºC (500ºF)
• UV, radiation, arc-track, ozone, steam, moisture and saltwater-resistant – steam/water pressure up to 120 psi
• Easily removable – just slice with knife and pull off – leaves no residue

• Order Number: MRCH-2002
• Dimensions:
  Frame: W48” x H54” x D21½”
• Caster Base: W48” x H3½” x D21½”
• Header: W48” x H11¾”
• Type of Unit: 4’ Free-Standing Gondola

• Inner Ring Adjusts 1/2" to 1-1/2" in Depth — Before or After Drywall Installation!

• Ideal storage conditions down to -20ºC
• Sizes 1/2” through 2”
• Colors can designate different voltages.
  Examples:
  - Yellow color for communication circuits
     and signaling cable
  - Red color for fire alarm circuits
  - Blue color for poser circuits

• Flat sides facilitate installation during rework applications.
• Team with a pair of CI820DX for a rugged installation.

• Raised for 5/8” thick drywall (4.3 cu. in.)

• Outdoor Nylon Cable Ties in a Rainbow of Colors, a T&B Exclusive

• Galvanized ground rod
• Copper Bonded steel ground rod
• Sectional type ground rods
• Coupling
• Driving studs
• Threadless coupling and driving caps standard copper bonded ground rods
• Type DGC - Drive-On Ground Clamps
• Galvanized grounding plate Ground Electrode Boxes
• Metallic Gradient Control Mat

• Easy to handle
• Available in convenient sizes
• Stackable
• Hinged cover
• Opens easily, closes securely
• Easy access.

• Modified silicone rubber compound
• Self amalgamating / bonding material. It only adheres to itself
• No adhesives or heat required for permanent bond
• Bond is immediate even if wet
• High dielectric value
• Insulation for high and low voltage connections
• High and low temperature stability (-90ºC to    260ºC) (-130ºF to 500ºF)
• Radiation resistant
• Arc track resistant
• UV and ozone resistant
• Steam / moisture resistant
• Will not contaminate fresh water and it is salt water resistant.